LevelOne GTL-5280 Manual de usuario Pagina 184
- Pagina / 264
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
176
3-18 Loop Protection
The loop Protection is used to detect the presence of traffic. When switch receives
packet’s(looping detection frame) MAC address the same as oneself from port, show Loop
Protection happens. The port will be locked when it received the looping Protection frames.
3-18.1 Configureaion
The section describes how to set Loop Protection.
Web Interface
To configure the Loop Protection parameters in the web interface:
1. Click Configuration,Loop Protection, Configuration
2. Evoke to select enable or disable the port loop Protection.
5. Click the Apply to Apply the setting
6. If you want to cancel the setting then you need to click the Reset button.
It will revert to previously Saved values
Figure 3-18.1: The Loop Protection Configuration.
Parameter description:
General Settings:
Enable Loop Protection:
Controls whether loop protections is enabled (as a whole). .
Transmission Time:
The interval between each loop protection PDU sent on each port. valid values are 1 to 10
seconds.
- GTL-5280 1
- INTRODUCTION 9
- GTL-5280 web help function: 12
- System Configuration 15
- 2-1.2 Configuration 17
- 2-1.3 CPU Load 18
- 2-2 Time 19
- 2-2.2 NTP 21
- 2-3.1 Users 22
- 2-3.2 Privitege Level 24
- 2-4.1 IPV4 26
- 2-4.2 IPV6 28
- 2-5 Syslog 29
- 2-5.2 Log 30
- 2-5.3 Detailed Log 31
- 2-6 SNMP 32
- 2-6.2 Communities 33
- 2-6.3 Users 34
- 2-6.4 Groups 36
- 2-6.5 Views 37
- 2-6.6 Access 39
- 2-6.7 Tarp 41
- Configuration 43
- 3-1.2 Port Description 45
- 3-1.3 Traffic Overview 46
- 3-1.4 Detailed Statistics 47
- Receive Error Counters 48
- Transmit Error Counters 48
- 3-1.5 Qos Statistics 49
- 3-1.6 SFP Information 50
- 3-2 ACL 52
- 3-2.2 Rate Limiters 54
- 3-2.3 Access Control List 55
- 3-2.4 ACL Status 58
- 3-3 Aggregation 60
- 3-3.2 LACP 62
- 3-4 Spanning Tree 69
- Basic Settings 70
- Advanced Settings 71
- 2-4.2 MSTI Mapping 72
- MSTI Mapping 73
- 3-4.3 MSTI Priorities 74
- 3-4.4 CIST Ports 75
- 3-4.5 MSTI Ports 77
- 3-4.6 Bridge Status 79
- 3-4.7 Port Status 80
- 3-4.8 Port Statistics 82
- 3-5 IGMP Snooping 83
- 3-5.2 VLAN Configuration 85
- 3-5.3 Port Group Filtering 87
- 3-5.4 Status 89
- 3-5.5 Group Infermation 91
- IGMP Group Table Columns 91
- 3-6 MLD Snooping 94
- 3-6.2 VLAN Configuration 97
- 3-6.3 Port Group Filtering 99
- 3-6.4 Status 100
- Web Interface 100
- 3-6.5 Group Infermation 102
- 3-6.6 IPv6 SSM Information 104
- 3-7 MVR 105
- 3-7.2 Groups Information 107
- 3-7.3 Statistics 108
- 3-8 LLDP 109
- LLDP Parameters 110
- LLDP Port Configuration 110
- 3-8.2 LLDP Neighbours 112
- 3-8.3 LLDP-MED Configuration 114
- Fast start repeat count 115
- Coordinates Location 115
- Civic Address Location 116
- Policies 117
- P) value (IETF RFC 2474) 117
- 3-8.4 LLDP-MED Neighbours 120
- 3-8.5 EEE 123
- 3-8.6 Port Statistics 125
- Local Counters 126
- 3- 9 Filtering Data Base 127
- MAC Table Learning 128
- 3- 9.2 Dynamic MAC Table 129
- Web Interface 129
- 3-10 VLAN 130
- 3-10.2 Ports 132
- Web Interface 132
- 3-10.4 Port Status 135
- 3-10.5 Private VLANs 137
- 3-10.5.1 Port Isolation 137
- 3-10.6 MAC-based VLAN 138
- 3-10.6.1 Configuration 138
- Web Interface 138
- 3-10.6.2 Status 140
- 3-10.7 Protocol -based VLAN 141
- 3-10.7.1 Protocol to Group 141
- 3-10.7.2 Group to VLAN 143
- 3-11 Voice VLAN 144
- 3-11.2 OUI 146
- 3-12 GARP 147
- 3-12.2 Statistics 149
- 3-13 GVRP 150
- 3-13.2 Statistics 152
- 3-14 QoS 153
- 3-14.2 Port Policing 155
- 3-14.3 Port Scheduler 157
- 3-14.4 Port Shaping 160
- 3-14.5 Port Tag Remarking 163
- 3-14.6 Port DSCP 165
- 3-14.7 DSCP-Based QoS 167
- 3-14.8 DSCP Translation 169
- 3-14.9 DSCP Classification 171
- : Edits the QCE 173
- 3-14.11 QCL Status 175
- 3-14.12 Storm Control 177
- 3-14.13 WRED 178
- 3-15 s-Flow Agent 180
- 3-15.2 Sampler 182
- 3-18 Loop Protection 184
- 3-18.2 Status 186
- 3-19 Easy Port 187
- 3-20 Mirroring 189
- Mirror Port Configuration 190
- 3-21 Trap Event Severity 191
- 3-23 UPnP 193
- Security 194
- 4-1.2 Static Table 196
- 4-1.3 Dynamic Table 197
- 4-2 ARP Inspection 198
- 4-2.2 Static Table 200
- 4-2.3 Dynamic Table 201
- 4-3 DHCP Snooping 202
- 4-3.2 Statistics 204
- 4-4 DHCP Relay 206
- 4-4.2 Statistics 208
- Client Statistics 208
- 4-5 NAS 210
- 4-5.2 Switch Status 217
- 4-5.3 Port Status 219
- Port State 219
- Port Counters 219
- Selected Counters 220
- Attached MAC Addresses 220
- VLAN ID 220
- 4-6 AAA 222
- 1. Check “Enabled” 222
- 4-6.2 Radius Overview 226
- RADIUS Accounting Servers 226
- 4-6.3 Radius Details 228
- 4-7 Port Security 229
- Port Configuration 230
- 4-7.2 Switch Status 232
- 4-7.3 Port Status 234
- 4-8 Access Management 235
- 4-8.2 Statistics 237
- 4-9 SSH 238
- 4-10 HTTPs 239
- 4-11 Auth Method 240
- Maintenance 241
- 5-2.1 Firmware Upgrade 242
- 5-2.2 Firmware Selection 243
- 5-3 Apply / Restore 245
- 5-4.1 Export Config 247
- 5-4.2 Import Config 248
- 5-5 Diagnostics 249
- 5-5.2 Ping6 250
- 5-5.3 VeriPHY 251
- Voice VLAN 264
Relacionado con productos y manuales para Los conmutadores de red LevelOne GTL-5280
(17 paginas)
(3 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.057 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales