LevelOne VOI-8001 Manual de usuario

1 VOI-8001 VOI-8002 VOI-8003 8-Port H.323/SIP VoIP Gateway User Manual Ver. 1.01-0610

1 3.2 System status This page reveals the status of the VoIP Gateway including WAN, LAN and some hardware/firmware information.

100 The Port Mapping page does a port range mapping. Server IP Set one of LAN client’s IP address to do port mapping. Mapping Ports Set the ports t

101 ALG Some applications have to do Application Level Gateway (ALG) to monitor the transaction or monitor the payload of the packet. This page l

102 DMZ Check this item to enable DMZ service. DMZ table This table lets you configure the DMZ hosts. If you have more than one public IP Addr

103 4.2.8.4 Firewall Firewall Options Enable Hacker Attack Protect The hackers always try to break into you system or crack down your network.

104scans all the TCP/UDP port of a station to find out the opened ports. After confirmed, the hackers try to connect to the listened ports to atta

105 Client Filtering Enable Client Filter Check this box and all the entries below will take effect. IP Block the IP addresses ranged to connect to

106 URL Filtering Enable URL Filter Check this box and all the entries below will take effect. IP The IP addresses ranged will be the candidate to

107 MAC Control MAC Control MAC Address Control Check this item to enable MAC control service. Filter out or only accept the following MAC address

108 4.2.8.5 Routing Routing Table This field indicates the destination IP of this route entry. Subnet Mask This field indicates the Subnet M

109 Static Routing Destination LAN IP This field indicates the destination IP of this route entry. Subnet Mask This field indicates the Subnet Mas

13.3 Register Server If this VoIP Gateway wants to use SIP Proxy or GateKeeper service to transfer the VoIP call, you can input the server informatio

110 4.2.8.6 UPnP Settings UPnP Enable UPnP Check this item to enable UPnP. UPnP Port Number Set UPnP port number to announce to the UPnP contr

111 Port Mapping Remote Host This field lists remote host that connect to LAN client. External Port This field lists the port of the remote host

112 4.2.8.7 DDNS Enabled Check this item to enable the DDNS settings Disabled Check this item to disable the DDNS settings Host Name Set your

113 4.2.9 Bandwidth & VLAN 4.2.9.1 Bandwidth Control You can enable WAN or LAN bandwidth control in this configuring page, so far only

114 4.2.10 Backup/Restore 4.2.10.1 Configuration /Backup-Restore/Configurations/ This page let you backup / Restore all of your configurat

115 4.2.10.2 VoIP Module /System Maintenance/Backup-Restore/Configurations/ This page displays the current firmware module version and let you

116 4.2.10.3 Reboot System /Reboot System Use the Reboot button on this page to reboot your VoIP Gateway, before you reboot, please make sure

117 4.2.11 Save Modification /Save Modification/ Most of the VoIP Gateway parameters will take effective after you modify, but it is just tempo

1 3.4 VoIP Call Out User key in the phone number through phone set dial pad, then VoIP Gateway translate the phone number by the routin

1 IP address, for example: 168.56.9.22  URL, route via URL. For example: www.inphonex.com .This VoIP Gateway can setup to register to DDNS servic

1 Chapter 4 Web UI Management 4.1 Access to Web UI The VoIP Gateway provide user friendly Web interface to let you configure your VoIP Gateway fu

14.2 Web UI Management The VoIP Gateway provide user friendly Web interface to let you configure your VoIP Gateway function and VoIP function. There

1 System Maintenance function  Configurations Backup/Restore  VoIP Module Backup/Restore  Reboot System  Save Modification Gateway Manua

14.2.2 VoIP Function 4.4.2.1 VoIP Setup/ Port Status/ This page will display the current and last time VoIP call status & result. a. The

1 Out: There is a phone call made from Network VoIP and pick up by phone set. e. Connected IP: The remotely party IP of this VoIP call. f. Caller

1 4.2.2.2 VoIP/Line Configure/ Line Setting /VoIP Setup/Line Configure/Line Setting/ This page will setup the phone line information each por

2Table of contents CHAPTER 1. INTRODUCTION ...3 1.1 OVERVIEW ...

2when you off hook the phone connected to the line 1, it will directly call to another VoIP gateway location at 168.56.09.22 and dial 601.

2 4.2.2.3 Line configure/ Tone Setting /VoIP Setup/Line Configure/ Tone Setting A.Call Progress Tone This page defines the tones generated to

2 Busy: Define the busy tone for generate.  Ring: Define the ring back tone for generate b. Low freq: Lower frequency for defined tone c. High

2 4.2.2.4 Line configure/ Line Feature /VoIP Setup/Line Configure/ Line Feature This page defines the feature on the phone port of the VoIP Gat

2 Current Drop-> 3 S: Enable FXS interface to generate three seconds Current Drop signal. C. Called Number Relay on FXS ： Define when use the

2 Line number Priority: The 1st line has high priority; it will always ring the 1st line if it is available. When 1st line is busy, it will try to

24.2.2.5 Line configure/ Line Polarity /VoIP Setup/Line Configure/ Line Polarity This page defines the Polarity on the phone port of the VoIP

2 4.2.2.6 Routing Setup/ VoIP Call Out Setting /VoIP Setup/Routing Setup/VoIP Call Out This page let you define the routing rule for Call out t

2translate for call out rule without needed to press # key. b. FirstDigitTime: Define the waiting time (seconds) for user press phone number first

2b. Remark: Remark for this routing rule. Please use UNDERLINE to replace the SPACE due to HTTP protocol limitation. c. Area Code: Define the P

3 Chapter 1. Introduction 1.1 Overview The VOI-800x series VoIP Gateway is equipped with 8 standard phone ports, one 10/100BaseTX Fast Ethernet WAN

3for gatekeeper 1. gk2 for gatekeeper 2. gk for all the gatekeepers available ( search sequence: gk1 > gk2 > gk3 > gk4). Gk3_2_1

3user press the number is 886212345678 and the STRIP field is setting to 4, the first 4 digits 8862 will be truncated and actually call out number wi

3C.Setting Examples Here is some VoIP call out routing table setting examples below: a. Define wait time and digits for destination phone number

3 Port Message Port Type Display name Status Connected IP Caller ID Start Time End Time Talking Sec Dialed number Release by 1 FXS Idle 172.16.7

3 Index Remark Area Code Min Digits Max Digits IP Address Strip Prefix Profile Delete 1 Take_All 86 10.1.1.1 2 Never_Used 8621

31 Via_GK2 1 gk2 35H35H35HDelete 2 GK2_3_1 2 gk2_3_1 36H36H36HDelete 3 GK_ALL 3 gk 37H37H37H Delete By Inde

32 UsePF2 2 10.1.1.2 PF2 41H41H41H Delete 3 UseDefaultPF 3 Gate.proxy.com 42H42H42H Delete Index Name VAD CODEC H.245 Tun

3 4.2.2.7 VoIP Call In Routing Table Setting /VoIP Setup/Routing Setup/VoIP Call In/ This page let you define the routing rule for Call in from

3b. Auth：Authorization IP check enable. Enable IP range authorization function. When Enable, the gateway will check the remote caller IP range setti

3 Index Area Code Strip Prefix Maximum Minimum From To LineNo Gatekeeper Alert Profile Forward Delete 1 90 2 0,12345678 51H51H51HD

4 1.3 Key Feature VoIP  Support 8 simultaneous VoIP calls  Support T.38 FAX relay  Support QoS(ToS) for VoIP  Compliant with H.323 / SIP Vo

4h. To: Define the ending line number for service this area code VoIP call. Index Area Code Strip Prefix Maximum Minimum From To LineNo Gatekee

4k. Call Waiting：Enable or Disable the call waiting function。  Enable: During Talk, you can answer another phone call and hold the origina

4 ID1 AS ID2 AS ID3 AS ID4 AS Delete 1 PF1 ON G.723.1 ON Out band ON 3 ON 00001 H.323 1001 E.164 66H66H 66HDelete 2 PF

410.1.1.1/104, it mean it will forward this call to IP 10.1.1.1 and calling number will change to 104). When the line 1 user is going to

44.2.2.8 VoIP Call In IVR Setting /VoIP Setup/Routing Setup/VoIP Call In IVR/ When Enable the [Prompt Voice for VoIP Call In function on /VoIP S

4A. Time & Digits wait for user The VoIP Gateway wait user input the number digits & time parameters as below: Time & Digi

4c. Min Digits: define the minimum digits wait for user press for number fit this rule, if user press digits less the number defined here.

4 4.2.2.9 VoIP Routing Profile Setting /VoIP Setup/Routing Setup/Routing Profile/ This page defines the optional special VoIP parameters when m

4 When select In band to transfer the DTMF during VoIP, the user pressed DTMF tone will be treat as general voice and been compressed then transmit

4 Please remember to press the modify button to take it effect. For store back to flash memory, please press Save Modification (/System Maintenance/

5 Chapter 2 Getting Started 2.1 Front Panel VOI-8001 VOI-8002 VOI-8003 (Ready) Flash: It means when the VoIP Gateway registration fail. (Re

5 4.2.2.10 VoIP Forwarding Profile Setting /VoIP Setup/Routing Setup/Forwarding/ This page defines the forwarding behavior include:  get an u

5f. No Answer Sec. Defined the wait seconds for redirect forward to another IP(or URL). g. Delete: Delete this rule item on routing table. h. To

5mean any call number with prefix 601 will always be forward to another VoIP Gateway locate at hk.big.com and dial out number is 301. When the line

51.4.2.11 VoIP Authorization Setting /VoIP Setup/Routing Setup/Authorization/ When this gateway has been used for outbound call, it can enable

54.2.3 Register Server Setting 4.2.3.1 Register Status /VoIP Setup/Register Server/Register Status You Can check the register status of thi

5 4.2.3.2 Setup the Register Server—SIP Protocol /VoIP Setup/Register Server/Server If you need use this gateway to register to the

5  Disable Register SIP Proxy server function. d. SIP Proxy URL: Please input the IP/URL of the SIP proxy server. e. Port [1~65535]: Port

5 q. Conference ID: Some SIP Server requires an ID to enable the conference function, please input the ID here to enable that. r. Enab

54.2.3.4 Setup the Register Server—H.323 Protocol /VoIP Setup/Register Server/Server When Select use H.323 to register gatekeeper, please input t

5 FXO: Analog phone interface for connect to PSTN or PBX extension line  FXS: Analog phone interface for connect to phone set or

6 2.2 Rear Panel VOI-8001 VOI-8002 VOI-8003 DC12V: For the included power adapter. Be sure to use only the 12VDC/2A power adapter included with

6 4.2.4 Auto Provision function To use the auto provision function, the system have to install a dedicate Auto Provision Server for keep

6It will indicate the status of linking to each Provision Servers. The gateway will link to one of the five setting Provision Server each time. If

62 4.2.5 Advance Setup 4.2.5.1 NAT Traversal /VoIP Setup/Advance Setup/NAT Traversal If your VoIP gateway is installed behind NAT,

63 4.2.5.2 Listen Port /VoIP Setup/Advance Setup/Listen Port In this page, user can define the usage port for setup the VoIP communication. Both

64 4.2.5.3 VoIP Package /VoIP Setup/Advance Setup/VoIP Package User can define the parameters relative about VoIP package on this page. 

65  RFC2833: Payload number for DTMF[96~127]: Define the DTMF token on RFC2833, input range form 96 to 127.  RTP Packet NAT Detect By: User can

66 4.2.5.4 RTP Packet Summary /VoIP Setup/Advance Setup/RTP Packet Summary On this page, user will know the RTP package summary about last VoI

67 4.2.5.5 Flash & Call waiting /VoIP Setup/Advance Setup/Flash & Call waiting On this page, user can define the parameters relative t

68 4.2.5.6 Gain /VoIP Setup/Advance Setup/Gain This page defines different function gain on the gateway.  Gain when Dial tone phase： When

69 This item allows user to adjust the talking volume of the device, which means it will affects all ports of this device, User can select the db val

7 Chapter 3 Configuration The default setting of DHCP Server inside VoIP Gateway is turn ON, So please set up your PC TCP/IP network as “Get IP A

70 4.2.5.7 QoS /VoIP Setup/Advance Setup/QoS User can define the ToS field on the VoIP packet for Quality of Service control. The ToS field is

71 4.2.5.8 CDR /VoIP Setup/Advance Setup/CDR The Gateway can export all the CDR (Call detail Record) to external CDR server by HTTP protocol.

72 4.2.5.9 FoIP /VoIP Setup/Advance Setup/FoIP User can define the parameters relative FAX Over IP function.  FAX Mode Appoint the FAX mode

73 Enable or Disable to send the double packet function during high speed T.38 FoIP.

74 4.2.5.10 Prompt Voice&Beep /VoIP Setup/Advance Setup/Prompt Voice & Beep This gateway can use voice or beep to prompt the user diff

75  Prompt voice for replace dial tone: Use a customize voice file to replace the dial tone  Warming Prompt after VoIP out failure: Annunciat

76 4.2.6 Application 4.2.6.1 Ping test /VoIP Setup/Application/Ping Test User can use the Ping Test function to test the network status

77 4.2.6.2 Telnet & SNMP /VoIP Setup/Application/Telnet & SNMP User can enable and set the user account for the SNMP and Telnet functi

78 4.2.6.3 Call Timer /VoIP Setup/Application/Call Timer The gateway can enable to set the limit communication time to Line port by Area Code

79  4.2.7 System 4.2.7.1 System Status This page reveals the status of the gateway including WAN, LAN and some hardware information. In

8 3.1 Connection Click “Connected Type” option below “System Setup\Wan” item: To use Static-IP ADSL connection, please select “Static IP

80 Cable/DSL This field indicates the Internet connection status. Its value is Connected , Disconnected or Connecting. WAN IP Connected to the In

81 Connection Type There are five ways to get the WAN IP address. They are DHCP, STATIC, PPPoE, PPTP and L2TP. This field indicates the way to get t

82 Short for Media Access Control address, a 96H96H 96Hhardware address that uniquely identifies each 97H97H97Hnode of a network. This field indic

83 4.2.7.2 System Settings This page is used to configure the names given by the ISP, if any, to represent the gateway, and also to set the local

84 4.2.7.3 Date & Time This page is used to setting the system time of VoIP gateway; it can define the correct time by which ways.

85 4.2.7.4 Administrator Setting This page allows you to change the user and administration password used to manage this VoIP Gateway for securi

86 4.2.7.5 System Log The system log page shows the gateway’s activity logs such as the Internet connectivity, hacker attack, intrusion detection

87 Remote Log Settings Remote Log Check this file and the gateway will send the log message to the “Send Log to” remote host. Send Log to Set th

88 4.2.8 Route Function(/System Setup) 4.2.8.1 Setting WAN connection: System Setup/Connection /System Setup/WAN/Connected Type Connectio

89 Request IP address You can specify the IP address you desired. But the ISP has the right to neglect it and provides you a different one. MTU

9 To use PPPoE ADSL connection, please select Yes in use “PPPoE” ADSL service and enter the “username” and “password” in the PPPoE setup section. M

90 IP address assigned by your ISP Set the IP address that assigned by the ISP. Subnet Mask Set the subnet mask of the network. ISP Gateway Addre

91 This page is the PPPoE configuration page. Most of the ISPs request the user to connect to central office (CO) side via PPPoE, acronym of Poin

92 that the user does not have to worry about the MTU size, the gateway routing engine will handle the MTU differences between PPP and the LAN Ethern

93 User can set this device work as a bridge, set the necessary information. A network bridge connects multiple network segments at the data link la

94 Static DNS Server Check this item to make the primary and secondary DNS server at the next two rows active. If this field is not enabled, the s

95 4.2.8.2 LAN Settings /S/System Setup/LAN/LAN Settings/ The home gateway is an IP sharing device, which provides the home users share the sam

96 IP Pool Ending Address The ending address provided by DHCP service. Lease Time Set the lease time of the IP address to renew. Local Domain Name

97 This column shows the host name of the DHCP clients. IP Address This column shows the IP Address of the DHCP clients. MAC Address This column sh

98 4.2.8.3 NAT Virtual Server This is the virtual server page, which set the rules translate the private IP/private port pairs to the public

99 Special Application Trigger Port To define the TCP/UDP port range to monitor, when initiating from the home network, the public ports configured