LevelOne 22Mbps Manual de usuario

1 LevelOne WBR-2401 22Mbps Wireless ADSL Firewall/VPN router w/Printer Server User`s Manual

10 Figure 2-3 Setup of LAN and WAN connections for this product. 3. Setup ADSL connection Prepare an telephone cable for connecting this product t

11Chapter 3 Network Settings and Software Installation To use LevelOne WBR-2401 correctly, you have to properly configure the network settings of y

123.2 Install the Software into Your Computers Skip this section if you do not want to use the print server function of this product. Step 1: Inse

13Step 4: When the following window is displayed, click on the Finish button. Step 5: Select the item to restart the computer and then click the OK

14Chapter 4 Configuring Wireless ADSL Broadband Router LevelOne WBR-2401 provides Web based configuration scheme, that is, configuring by your We

154.2 Status This option provides the function for observing this product’s working status: A. WAN Port Status. If the WAN port is assigned a dy

16 Notice: For the WBR-2401B, it can support both Annex B and U-R2 ADSL line coding schemes. The default setting is Annex B. If your ISP used U-R2 sc

17 Setup Wizard will guide you through a basic configuration procedure step by step. Press ”Next >” Setup Wizard - Select WAN Type: For deta

18 4.4 Basic Setting

19 4.4.1 Primary Setup – WAN Type Press “Change”

2 FCC Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of t

20 This page is primary to enable LevelOne WBR-2401 to work properly. The setting items and the web appearance depend on the WAN type. Choose correct

214.3.2.1 Ethernet Over ATM (RFC 1483 Bridged) without NAT This WAN type disable the NAT, this device becomes a pure bridge between your LAN and WAN

224.3.2.2 Ethernet Over ATM (RFC 1483 Bridged) with NAT A. Static IP Address: ISP assigns you a static IP address: WAN IP Address, Subnet Mask, Gat

23 B. Dynamic IP Address: Obtain an IP address from ISP automatically. Host Name: optional. Required by some ISPs, for example, @Home. Renew IP Fore

24 4.3.2.3 IP over ATM (RFC 1483 Routed): In the Router Mode, NAT is always enabled. You have to set the following WAN IP settings: WAN IP Mode:

25 VPI/VCI Numbers: The channel settings provided by your ISP. Schedule Type: The setting of the ADSL traffic schedule type. This device supports

26 WAN IP Mode: This product supports two WAN IP modes: static and dynamic. If you select dynamic mode, it will try to get a legal IP and WAN setting

274.3.2.5 PPP over ATM: Press “More >>”

28 PPPoA Account/Password: The account ID & password provided by your ISP. Maximum Idle Time: The time of no activity disconnect to your PPPo

29Optional. Required by some ISPs. Once you finished the required configuration, you must click on the "Save" button to save the configurat

3Table of Contents Chapter 1 Introduction... 5

30 PPPoE Account/Password: The account ID & password provided by your ISP. Maximum Idle Time: The time of no activity disconnect to your PPPoE s

31Optional. Required by some ISPs. Once you finished the required configuration, you must click on the "Save" button to save the configurat

324.3.3 OAM Setup In this page, you can set the OAM feature for virtual channel. First click on the Enable or Disable circle for the settings of O

33 4.4.2 DHCP Server Press “More>>”

34 The settings of a TCP/IP environment include host IP, Subnet Mask, Gateway, and DNS configurations. It is not easy to manually configure all t

35This function enables you to assign another gateway to your PC, when DHCP server offers an IP to your PC. 4.4.3 Wireless Setting, and 802.1X setti

36word or phrase into hex. 6. 802.1X Setting 802.1X CheckBox was used to switch the function of the 802.1X. When the 802.1X function is enable, t

37 4.4.4 Change Password You can change Password here. We strongly recommend you to change the system password for security reason.

38 4.5 Forwarding Rules

39 4.5.1 Virtual Server This product’s NAT firewall filters out unrecognized packets to protect your Intranet, so all hosts behind this product are

44.8 Toolbox ...74 4.8.1 View Log...

40 4.5.2 Special AP Some applications require multiple connections, like Internet games, Video conferencing, Internet telephony, etc. Because of t

414.5.3 Miscellaneous Items IP Address of DMZ Host DMZ (DeMilitarized Zone) Host is a host without the protection of firewall. It allows a computer

42 4.6 Security Settings

43 4.6.1 Packet Filter Packet Filter enables you to control what packets are allowed to pass the router. Outbound filter applies on all outbound pa

44addresses (4.3.2.1-4.3.2.254). An empty implies all IP addresses. For source or destination port, you can define a single port (80) or a range of

45 Example 2: (192.168.123.100-192.168.123.119) They can do everything except read net news (port 119) and transfer files via FTP (port 21) Other

46 (192.168.123.100-192.168.123.149) They are allowed to send mail (port 25), receive mail (port 110), and browse Internet (port 80); port 53 (DNS)

47transfer files via FTP (port 21) Others are allowed After Outbound Packet Filter setting is configured, click the save button.

48 4.6.2 Domain Filter Domain Filter let you prevent users under this device from accessing specific URLs. Domain Filter Enable Checke if you wan

49Example: In this example: 1. URL include “sex.com” will be blocked, and the action will be record in log-file. 2. URL include “girl.com” will not

5Chapter 1 Introduction Congratulations on your purchase of this outstanding LevelOne WBR-2401 22MbpsWireless ADSL Firewall/VPN Router. w/Printer Po

504.6.3 MAC Address Control MAC Address Control allows you to assign different access right for different users and to assign a specific IP address

51addresses are not in the "Control table", to associate to the wireless LAN. Control table "Control table" is the table at the b

52 4.6.4 VPN setting VPN Settings are settings that are used to create virtual private tunnels to remote VPN gateways. The tunnel technology suppor

53System managers of both end gateways only need set the same pre-shared key. Function of Buttons More: To setup detailer configuration for manual

54 Local netmask Local netmask combined with local subnet to form a subnet domain.  Remote subnet The subnet of LAN site of remote VPN gateway, i

55•VPN Settings - Set IKE Proposal  IKE Proposal index A list of selected proposal indexes from the IKE proposal pool listed below. The selecting ac

56 •VPN Settings -Set IPSec Proposal  IPSec Proposal index A list of selected proposal indexes from the IPSec proposal pool listed below. The select

57IPSec proposal.  Life time The unit of life time is based on the value of Life Time Unit. If the value of unit is second, the value of life time

58 4.6.5 Miscellaneous Items Remote Administrator Host/Port In general, only Intranet user can browse the built-in web pages to perform administrat

59 4.7 Advanced Setting

6Packet Filter allows you to control access to a network by analyzing the incoming and outgoing packets and letting them pass or halting them based o

60 4.7.1 ADSL Modem Performance Setting Tx Gain Offset This parameter allows the user to add an offset on the Tx gain of the CPE Modem. The offset

61offset. Tx Output Power Offset This parameter allows user to reduce the Tx output power (in the upstream direction). The value should be ranged b

62 4.7.2 System Time Get Date and Time by NTP Protocol Selected if you want to Get Date and Time by NTP Protocol. Time Server Select a NTP time

63 4.7.3 System Log This page support two methods to export system logs to specific destination by means of syslog(UDP) and SMTP(TCP). The items you

64E-mail Subject The subject of email alert. This setting is optional.

65 4.7.4 Dynamic DNS To host your server on a changing IP address, you have to use dynamic domain name service (DDNS). So that anyone wishing to

66Username/E-mail Password/Key You will get this information when you register an account on a Dynamic DNS server. Example: After Dynamic DNS setti

67 4.7.5 SNMP Setting In brief, SNMP, the Simple Network Management Protocol, is a protocol designed to give a user the capability to remotely mana

68 1. This device will response to SNMP client which’s get community is set as “public” 2. This device will response to SNMP client which’s set commu

69 4.7.6 Routing Table Routing Tables allow you to determine which physical interface address to use for outgoing IP data grams. If you have more t

7! Schedule Rule You can set the schedule time to decide which service at what time will be turned on or off. Packing List ! WBR-2401 22Mbps Wire

70 Example: So if, for example, the host wanted to send an IP data gram to 192.168.3.88, it would use the above table to determine that it had to

71 4.7.7 Schedule Rule You can set the schedule time to decide which service at what time will be turned on or off. Select the “enable” item. Pre

72

73 Schedule Enable Selected if you want to Enable the Scheduler. Edit To edit the schedule rule. Delete To delete the schedule rule, and the ru

74 4.8 Toolbox

75 4.8.1 View Log You can View system log by clicking the View Log button

76 4.8.2 Firmware Upgrade You can upgrade firmware by clicking Firmware Upgrade button.

77 4.8.3 Backup Setting You can backup your settings by clicking the Backup Setting button and save it as a bin file. Once you want to restore thes

784.8.6 Miscellaneous Items MAC Address for Wake-on-LAN Wake-on-LAN is a technology that enables you to power up a networked device remotely. In or

79 Chapter 5 Print Server LevelOne WBR-2401 provides the function of network print server for MS Windows 95/98/NT/2000 and Unix based platforms.

8 LED: LED Function Color Status Description POWER Power indication Green On Power is being applied to this product. M1 System status 1 Green Bl

801. Find out the corresponding icon of your server printer, for example, the HP LaserJet 6L. Click the mouse’s right button on that icon, and then

81 3. Choose the “PRTmate: (All-in-1)” from the list attached at the Print To item. Be sure that the Printer Driver item is configured to the corre

825.2 Configuring on Windows NT Platforms The configuration procedure for a Windows NT platform is similar to that of Windows 95/98 except the screen

835.3 Configuring on Windows 2000 and XP Platforms Windows 2000 and XP have built-in LPR client, users could utilize this feature toPrint. You have

84 2. Select “Ports” page, Click “Add Port…”

853. Select “Standard TCP/IP Port”, and then click “New Port…” 4. Click Next and then provide the following information: Type address of server p

86 5. Select Custom, then click “Settings…”

876. Select “LPR”, type ” lp“ lowercase letter in “Queue Name:” And enable “LPR Byte Counting Enabled”. 7. Apply your settings

88

895.4 Configuring on Unix based Platforms Please follow the traditional configuration procedure on Unix platforms to setup the print server of this p

9 2.1.2. Rear Panel Figure 2-2 Rear Panel Ports: Port Description 5VDC Power inlet: DC 5V, 2.5A (minimum) WAN The port where you will connect your

90 Appendix A TCP/IP Configuration for Windows 95/98 This section introduces you how to install TCP/IP protocol into your personal computer. And

915. Select Microsoft item in the manufactures list. And choose TCP/IP in the Network Protocols. Click OK button to return to Network window. 6.

924. Now, you have two setting methods: A. Get IP via DHCP server a. Select Obtain an IP address automatically in the IP Address tab. b. Don’t

93c. Choose Disable DNS in the DNS Configuration tab. B. Configure IP manually a. Select Specify an IP address in the IP Address tab. The defau

94b. In the Gateway tab, add the IP address of this product (default IP is 192.168.123.254) in the New gateway field and click Add button. c. In

95 Appendix B Main ISP setting for ADSL modem configuration. Argentina : Argentina Telecom : Encapulation : RFC 1483 Bridge LLC VPI :

96 Encapulation : RFC 1483 Bridge LLC VPI : 0 VCI : 100 Handshack protocal : Autosense-G.dmt first France : France Teleco

97 Israel : Israel : Encapulation : RFC 2364 PPPoA VC-Mux VPI : 8 VCI : 48 Handshack protocal : Autosense-G.dmt first It

98 Handshack protocal : Autosense-G.dmt first New Zealand : New Zealand Telecom : Encapulation : RFC 2364 PPPoA VC-Mux VPI : 0

99BT : Encapulation : RFC 2364 PPPoA VC-Mux VPI : 0 VCI : 38 Handshack protocal : Autosense-G.dmt first Encapsulation